Open Access System for Information Sharing

Browse by Researchers

KIM, HYOUNG SEOP(김형섭) orcid researcherid google scholar scopus

Department: Ferrous & Eco Materials Technology(친환경소재대학원)

Major(s): -

E-Mail

Homepage

Co-researchers

Keyword

Publication & Time Cited Count (For the Last 5 years)

Results 21-40 of 99 (Search time: 0.002 seconds).

Applied search limites :

Date Issued : [2010 TO 2019] Subject : BEHAVIOR

Article

Continuum understanding of twin formation near grain boundaries of FCC metals with low stacking fault energySCIESCOPUS

npj Computational Materials, vol. 3, 2017-05

Article

On the rule-of-mixtures of the hardening parameters in TWIP-cored three-layer steel sheetSCIESCOPUSKCI

METALS AND MATERIALS INTERNATIONAL, vol. 23, no. 3, page. 1 - 6, 2017-04

Article

Novel 1.5 GPa-strength with 50%-ductility by transformation-induced plasticity of non-recrystallized austenite in duplex steelsSCIESCOPUS

Scientific Reports, vol. 7, no. 1, 2017-04

Article

On the strain rate dependent deformation mechanism of CoCrFeMnNi high-entropy alloy at room and liquid nitrogen temperaturesSCIESCOPUS

Materials Research Letters, vol. 5, no. 7, page. 472 - 477, 2017-03

Article

Influences of high strain rate, low temperature, and deformation direction on microstructural evolution and mechanical properties of copperSCIESCOPUS

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, vol. 684, page. 567 - 576, 2017-01

Article

Quasi-static and dynamic deformation mechanisms interpreted by microstructural evolution in TWinning Induced Plasticity (TWIP) steelSCIESCOPUS

Metallurgical and Materials Transactions A, vol. 684, page. 54 - 63, 2017-01

Article

Development of an oxide-dispersion-strengthened steel by introducing oxygen carrier compound into the melt aided by a general thermodynamic modelSCIESCOPUS

Scientific Reports, vol. 6, 2016-12-12

Article

Factors governing hole expansion ratio of steel sheets with smooth sheared edgeSCIESCOPUSKCI

METALS AND MATERIALS INTERNATIONAL, vol. 22, no. 6, page. 1009 - 1014, 2016-11

Article

Ring-Constraint High-Pressure Torsion ProcessSCIESCOPUS

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, vol. 47A, no. 7, page. 3473 - 3478, 2016-07

Article

Effects of Effective Dendrite Size on Dynamic Tensile Properties of Ti-Based Amorphous Matrix CompositesSCIESCOPUS

Metallurgical and materials Transactions A, vol. 47A, no. 4, page. 1504 - 1509, 2016-04

Article

Obtaining Reliable True Plastic Stress-Strain Curves in a Wide Range of Strains Using Digital Image Correlation in Tensile TestingSCIESCOPUSKCI

KOREAN JOURNAL OF METALS AND MATERIALS, vol. 54, no. 4, page. 231 - 236, 2016-04

Article

Real Hydrostatic Pressure in High-Pressure Torsion Measured by Bismuth Phase Transformations and FEM SimulationsSCIESCOPUS

Materials Transactions, vol. 57, no. 4, page. 533 - 538, 2016-04

Article

Microstructure and high-temperature mechanical properties of the Mg-4Zn-0.5Ca alloy in the as-cast and aged conditionsSCIESCOPUS

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, vol. 649, page. 441 - 448, 2016-01

Article

Strain Softening Induced by High Pressure Torsion in Copper AlloysSCIESCOPUS

Materials Transactions, vol. 56, no. 10, page. 48 - 53, 2015-10

Article

Dynamic tension-compression asymmetry of martensitic transformation in austenitic Fe-(0.4,1.0)C-18Mn steels for cryogenic applicationsSCIESCOPUS

ACTA MATERIALIA, vol. 96, page. 37 - 46, 2015-09-01

Article

Effect of starting materials on the wear performance of NiTi-based compositesSCIESCOPUS

WEAR, vol. 334, page. 35 - 43, 2015-07-15

Article

Off-Axis Twist Extrusion for Uniform Processing of Round BarsSCIESCOPUSKCI

METALS AND MATERIALS INTERNATIONAL, vol. 21, no. 4, page. 734 - 740, 2015-07

Article

Effect of high-pressure torsion on the microstructure and strengthening mechanisms of hot-consolidated Cu-CNT nanocompositeSCIESCOPUS

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, vol. 638, page. 289 - 295, 2015-06-25

Article

Using dilatometry to study martensitic stabilization and recrystallization kinetics in a severely deformed NiTi alloySCIESCOPUS

JOURNAL OF MATERIALS SCIENCE, vol. 50, no. 11, page. 4003 - 4011, 2015-06

Article

Unique Appearance of Lamellar Cleavage Patterns on Fracture Surfaces of Ti-Based Amorphous Matrix CompositeSCIESCOPUS

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, vol. 46A, no. 6, page. 2506 - 2515, 2015-06

1 2 3 4 5

Open Access System for Information Sharing

Co-researchers

Keyword

Publication & Time Cited Count (For the Last 5 years)

Date issued

Type

Subject

Journal Registered

Browse